Single Family Alteration

1. Wall stud spacing and sizeCritical

   Verify stud size and spacing match approved plans

   FBC-R R602.3
2. Headers and beamsCritical

   Verify header and beam sizes over openings per plans

   FBC-B 110.3
3. Top and bottom plate connectionsCritical

   Verify plate configuration, laps and anchorage against the approved framing design; do not assume double top plates.

   FBC-B 110.3
4. Corner and intersection bracingCritical

   Verify proper bracing at corners and wall intersections

   FBC-B 110.3
5. Window and door rough openingsCritical

   Verify rough openings match approved plans for size and location

   FBC-B 110.3
6. Hurricane straps and hold-downsCritical

   Compare roof-to-wall connectors and straps with the approved high-wind design and connector schedule.

   FBC-R R301.2.1.1
7. Fire blockingCritical

   Verify fire blocking is installed at required locations

   FBC-R R302.11

1. Underlayment installationCritical

   Verify roof underlayment is installed per code and manufacturer specs

   FBC-R R905.1.1

1. Supply pipe sizing and materialCritical

   Compare supply pipe material with plans and sizing with approved water-distribution design.

   FBC-P 604.3FBC-P 605.4
2. DWV pipe sizing and slopeCritical

   Compare DWV pipe sizes with approved plans and measure horizontal drain slope.

   FBC-P 704.1
3. Pipe support and hangingCritical

   Verify pipes are properly supported at required intervals

   FBC-P 308.1
4. Vent termination locationsCritical

   Verify the vent terminates outdoors through an approved roof or sidewall method shown on plans.

   FBC-P 903.1
5. Water heater rough-inCritical

   Where a water heater is in scope, compare location and connections with approved plans and instructions; show pan where leakage could cause damage.

   FBC-P 502.1FBC-P 504.7

1. Panel installationCritical

   Verify panel rating and overcurrent protection match approved design, with clear working space.

   NEC 408.36NEC 110.26
2. Wire sizing per circuitsCritical

   Verify wire gauge matches breaker amperage for each circuit

   NEC 310.16NEC 240.4
3. Box fill and installationCritical

   Verify electrical boxes are properly installed and not overfilled

   NEC 314.16
4. GFCI and AFCI locationsCritical

   Verify GFCI and AFCI protection is provided where required

   NEC 210.8NEC 210.12
5. Alarm locations, power provisions and interconnection methodCritical

   When alarms are in the approved scope, identify planned smoke and CO alarm locations, exposed smoke-alarm power provisions and the approved wired or listed wireless smoke interconnection method. Record the permitted CO power method; installed devices are checked at final.

   FBC-R R314.3FBC-R R314.4FBC-R R314.6FBC-R R315.1FBC-R R315.1.1
6. Grounding and bondingCritical

   Show grounding electrode system and its approved electrode types and connections.

   NEC 250.50NEC 250.52

1. Ductwork installationCritical

   Verify duct sizes, routing, and support match approved plans

   FBC-M 603.1
2. Duct sealingCritical

   Verify duct joints and connections are properly sealed

   FBC-M 603.9
3. Equipment placementCritical

   Verify air handler and condenser locations per plans with required clearances

   FBC-M 304.1
4. Refrigerant line installationCritical

   Compare refrigerant piping routing and sizing with approved plans; leave field-made joints exposed before concealment.

   FBC-M 1107.1FBC-M 1107.7
5. Return air pathway

   Verify return air pathways are properly sized and located

   FBC-M 603.1

1. Wall cavity insulation R-valueCritical

   Verify wall insulation R-value matches energy calculations

   FBC-E R402.1.2
2. Ceiling/attic insulation R-valueCritical

   Verify ceiling or attic insulation R-value per energy calculations

   FBC-E R402.1.2
3. Insulation coverage and gapsCritical

   Verify no gaps, voids, or compression in insulation installation

   FBC-E R402.4.1.1
4. Air sealingCritical

   Verify air sealing at penetrations, top plates, and rim joists

   FBC-E R402.4.1.1

1. Drip edge installationCritical

   Verify drip edge is installed at eaves and rakes

   FBC-R R905.2.8.5
2. Valley and flashingCritical

   Verify valley flashing and wall flashing are properly installed

   FBC-R R903.2
3. Roof penetration sealing

   Verify all roof penetrations are properly sealed and flashed

   FBC-R R903.2
4. Covering materialCritical

   Match roof tile, shingles, or metal panels to the approved plans and product approval.

5. Covering attachmentCritical

   Show fastener or clip pattern before it is concealed by the next course.

6. Flashing installationCritical

   Show flashing at valleys, walls, edges, and penetrations while accessible.

1. Wall covering material and installationCritical

   Verify exterior wall covering material matches approved plans and is properly installed

   FBC-R R703.1
2. Weather-resistive barrierCritical

   Verify weather-resistive barrier is properly installed behind cladding

   FBC-R R703.2
3. Flashing at penetrations and transitionsCritical

   Verify flashing is installed at windows, doors, and wall transitions

   FBC-R R703.4
4. Fastener pattern and spacing

   Verify cladding fastener type and spacing per manufacturer and plans

   FBC-R R703.1

Most jurisdictions skip this inspection for this project type. Confirm with your building department whether they'll require it.

1. Board product and exposureCritical

   Compare board type and thickness with the approved assembly; use an approved tub/shower backer and do not use water-resistant gypsum in direct water exposure.

   FBC-R R702.3.7.1FBC-R R702.4.2
2. Fastener spacingCritical

   Verify screw or nail spacing meets code requirements

   FBC-R R702.3.5
3. Fire-rated assembliesCritical

   Where the garage-to-dwelling separation is in scope, compare gypsum layers, fastening and openings to the approved assembly.

   FBC-R R302.6

1. Panel complete and labeledCritical

   Verify panel cover installed, all breakers labeled, no open knockouts

   NEC 408.4
2. GFCI and AFCI operationalCritical

   Verify all GFCI and AFCI devices test and reset properly

   NEC 210.8NEC 210.12
3. Receptacle and switch functionCritical

   Operate affected receptacles and switches in this permit and show completed connections.

   FBC-B 110.3
4. Light fixtures installed

   Verify all light fixtures are installed and operational

   NEC 210.70
5. Exterior lighting and outletsCritical

   Where this permit changes exterior lighting or outlets, show operation and required GFCI protection.

   NEC 210.8NEC 210.70
6. Installed alarm devices and operation, if in scopeCritical

   When alarm installation is in this permit, confirm installed smoke and CO device locations and labels against the approved plan and permitted power method; demonstrate smoke-alarm interconnection and applicable device tests per manufacturer instructions.

   FBC-R R314.3FBC-R R314.4FBC-R R314.6FBC-R R315.1FBC-R R315.1.1

1. Fixture setting and alignmentCritical

   Verify in-scope fixtures are set level and aligned.

   FBC-P 405.3
2. Fixture connections and operationCritical

   Show affected fixtures connected to water and drainage systems, then demonstrate operation and check for visible leaks.

   FBC-P 301.3FBC-P 301.4
3. Water heater installationCritical

   If a storage heater is in scope, show installation, relief valve and discharge, and pan/drain where leakage could cause damage.

   FBC-P 502.1FBC-P 504.4FBC-P 504.6FBC-P 504.7
4. No visible leaksCritical

   Run affected fixtures or equipment and show new visible supply and drain connections remain dry.

5. Hose bibbs and exterior plumbingCritical

   Verify exterior hose bibbs have backflow prevention

   FBC-P 608.16.4.2

1. System operational testCritical

   Demonstrate only the permitted mechanical system operating per approved design and manufacturer instructions.

2. Air handler and condenser installationCritical

   Where air handler or condenser equipment is in scope, verify installation, access and clearances against approved plans and manufacturer instructions.

   FBC-M 304.1
3. Condensate drainCritical

   Verify condensate drain is properly routed and terminated

   FBC-M 307.2
4. Duct registers and grillesCritical

   Where ducts are in scope, show representative installed registers and grilles per manufacturer instructions.

   FBC-M 603.18
5. Equipment labels and data plates

   Show equipment nameplates and compare capacity and efficiency to the approved schedule.

1. Completed altered scopeCritical

   Show each changed structural, layout, and finish element against approved plans.

   FBC-B 110.3
2. Affected egress and safetyCritical

   If this work changes a bedroom, exit, or stair, show the resulting safe route and openings.

   FBC-R R310.1FBC-R R311.7
3. Affected rated or exterior assembliesCritical

   If work disturbs the garage-to-dwelling separation or exterior weather barrier, show the restored approved detail.

   FBC-R R302.6FBC-R R703.4